Bench test · 19 Nov 2026

Electronic dartboards: how the board knows where the dart landed

A soft-tip board is a matrix of switches behind a perforated face. Scoring accuracy is a mechanical problem, and most complaints about 'wrong scores' start at the face rather than the electronics.

A soft-tip board is a matrix of switches behind a perforated face. Scoring accuracy is a
A soft-tip board is a matrix of switches behind a perforated face. Scoring accuracy is a mechanical problem, and most complaints about 'wrong scores' start at the face rather than the electronics.

The switch matrix and the face

The board's face is a perforated plastic layer, and behind it sits a grid of switch segments arranged in the standard twenty sectors, doubles, trebles and bull. A dart tip passing through the holes closes a switch, and the controller reads the closure as a score.

The geometry is fixed by the game rather than by the design: twenty sectors at defined angles, doubles and trebles at defined radii, and a bull with an inner and an outer ring. A millimetre of radial error is a wrong treble.

The face's perforation pattern decides which switch a tip can reach. A hole that overlaps two segments lets a tip trigger the wrong one, and the user sees a score that is one segment off.

The design that avoids it uses a honeycomb pattern aligned to the switch grid, with the spokes between sectors wide enough that a tip landing on a spoke cannot close a switch at all.

Tip diameter, wear and the drift that follows

A soft tip is nominally 2.4 millimetres at the point, and it wears. A worn tip passes deeper and can close a switch through a neighbouring hole.

The tips are consumable, and the consumable's quality is part of the product's accuracy. A cheap tip that mushrooms at the point is a tip that produces phantom scores.

The board's face also wears. Repeated hits open the holes slightly, and after a few hundred thousand darts the face is looser and the accuracy falls.

The face should be a replaceable part with a published part number. A board whose face cannot be replaced is a board with a fixed number of accurate darts in it.

Bounce-out and the shot that scores nothing

A dart that hits a wire or a spoke and bounces out scores nothing, and the player sees a miss rather than an error. Bounce-out is a mechanical outcome, not a scoring fault.

The rate of bounce-out depends on the tip's hardness, the wire's thickness and the angle of the hit. A soft tip deforms and holds; a hard tip rebounds.

The wires between segments are the main cause of bounce-out on a soft board, and a board with thinner wires has a lower bounce-out rate. The trade is durability against accuracy.

A specification should state the bounce-out rate measured over a defined number of throws with a defined tip. Without that number, 'anti-bounce-out' is an adjective.

The controller, the debounce and the double count

A switch closure lasts a few milliseconds and bounces for part of that time. The controller debounces the signal, and the debounce window decides whether a fast double hit is counted once or twice.

A debounce that is too short counts a single dart twice when the tip vibrates in the hole. A debounce that is too long misses a genuinely fast second dart in the same segment.

The window is usually a few milliseconds, and it should be documented in the service manual because it is the setting most likely to be changed by a technician trying to fix a complaint.

The controller should also reject a closure that occurs while the previous dart is still being registered, which is the software version of the same problem.

Display, count and the game rules

The display's correctness is a rules problem rather than a hardware one. Cricket, 501 and Around the Clock each have their own scoring logic, and a bug in one game's logic looks like a hardware fault to the player.

The rules engine should be validated against a written ruleset for each game, with a test script that a support team can run. A board that cannot be validated is a board that generates support calls.

The display should show the last dart as well as the total, because the player needs to know which dart was registered when a score looks wrong.

A board with a dart history is a board whose complaints can be diagnosed. A board with only a total is a board whose complaints are arguments.

What to test before a container ships

Test fifty throws at each of the twenty sectors, with a defined tip and a defined throw distance, and record the misses and the phantom scores separately.

Test the bounce-out rate at the treble and double rings, which are the segments with the most wires per unit area and the most complaints.

Test the debounce by throwing two darts into the same segment within a second, and confirm the count. A board that scores one dart as two will be returned.

The test records belong in the technical file. A container that ships without them is a container whose quality is a hope.

The bull, the smallest target and the largest error

The bull is the smallest segment on the board, and it is where a millimetre of tolerance produces the most visible error. A hit that lands in the outer bull and scores the inner is a score the player remembers.

The switch geometry under the bull is denser than anywhere else, and the tip's diameter is a significant fraction of the segment's width.

The design should make the bull's switch single and centred, rather than a ring of small switches, so that the closure is unambiguous.

A board with a separate, larger bull switch has a better bull accuracy than one that shares a matrix cell with the ring around it.

Mounting, level and the throw that is always low

A board mounted at the wrong height produces a low scoring pattern, and the player blames the board. The height and the throw line are part of the game's definition.

The board should include a measuring guide or a marked throw line, and the manual should give both dimensions in metric and imperial.

A board that is mounted on a hollow door transmits the impact to the door, and the door's resonance can affect the switch matrix over time. The mounting method should be specified.

A wall-mounted board with a bracket that is not level produces a bias in one direction, which looks like a scoring fault rather than a mounting fault.

The supply, the surge and the board that resets

A dartboard's supply is small, and a supply that is shared with a bar's refrigeration can see surges that reset the controller mid-game.

The board should have a brown-out reset with a defined behaviour: a reset that loses the game is worse than a reset that preserves the score.

The supply's isolation and its surge protection are part of the product's reliability, and they belong on the specification rather than in the manual's small print.

A board that resets once a week is a board that will be replaced, and the cause is usually the supply rather than the board.

The score that is right and the player who disagrees

A board can be correct and still be argued with, because the player saw the dart land and the board registered a different segment.

The dart's history with the segment it registered is the evidence, and a board that stores the last twenty darts with their positions can settle the argument.

The board's face and its switch grid are the arbiter, and the display should show the registered segment rather than only the score.

A board that shows the segment is a board that ends the argument, and the feature is software rather than hardware.

The short version

The board's accuracy is a mechanical property of the face, the tip and the switch grid, and the electronics only report what the mechanism registers.

A replaceable face, a defined tip and a documented debounce window are the three items that keep a score honest through a season of play.

Test fifty throws per sector before a container ships, and record the phantom scores separately from the misses. The two numbers diagnose different faults.

The board whose face is aligned to the switch grid is the electronic dartboard, and its replaceable face is the part that keeps the accuracy claim honest over a season.

What to check

  • Face perforation aligned to the switch grid, with wide spokes
  • Tip specification and its effect on accuracy
  • Face replaceable, with a published part number
  • Bounce-out rate measured on a defined sample
  • Debounce window documented in the service manual
  • Rules engine validated per game with a test script